docker flannel网络部署和路由走向分析

1.flannel介绍

flannel是coreos开发的容器网络解决方案。flannel为每一个host分配一个subnet，容器今后subnet中分配ip。这些ip能够在host间路由，容器间无需nat和port mapping就能够跨主机通信。

每一个subnet都是从一个更大的ip池中划分的，flannel会在每一个主机上运行一个叫flanneld得agent，其职责是从ip池中分配subnet。为了在各个主机间共享信息，flannel用etcd存放网络配置，已分配的subnet，host的ip等信息。

数据包经过backend在主机间转发。
flannel提供了多种backend，最经常使用的有vxlan和host-gw。

2.部署实验环境

三个虚机

docker1 docker2 docker3 

etcd安装在docker1
docker1 docker2 docker3上运行flanneld
注:为了更方便的验证flannel和etcd因此docker1也安装了flannel，

其实能够不用在docker1安装
centos7自带了软件包，直接yum安装便可
2.1 
安装配置etcd

yum -y install etcd
[root@docker1 ~]# systemctl start etcd  && systemctl enable etcd
[root@docker1 ~]#

测试下

[root@docker1 ~]# etcd --version
etcd Version: 3.2.18
Git SHA: eddf599
Go Version: go1.9.4
Go OS/Arch: linux/amd64
[root@docker1 ~]#

[root@docker1 ~]# etcdctl set test "a"
a
[root@docker1 ~]# etcdctl get test
a
[root@docker1 ~]#

2.2 

安装配置flannel

[root@docker1 ~]# yum -y install flannel

启动

[root@docker1 ~]# systemctl start flanneld

报错

[root@docker1 ~]# systemctl status flanneld -l
● flanneld.service - Flanneld overlay address etcd agent
   Loaded: loaded (/usr/lib/systemd/system/flanneld.service; disabled; vendor preset: disabled)
   Active: activating (start) since Thu 2018-06-14 02:22:26 EDT; 1min 1s ago
Main PID: 2950 (flanneld)
   Memory: 16.6M
   CGroup: /system.slice/flanneld.service
           └─2950 /usr/bin/flanneld -etcd-endpoints=http://127.0.0.1:2379 -etcd-prefix=/atomic.io/network

Jun 14 02:23:18 docker1 flanneld-start[2950]: E0614 02:23:18.974351    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:19 docker1 flanneld-start[2950]: E0614 02:23:19.977497    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:20 docker1 flanneld-start[2950]: E0614 02:23:20.980721    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:21 docker1 flanneld-start[2950]: E0614 02:23:21.983553    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:22 docker1 flanneld-start[2950]: E0614 02:23:22.988446    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:23 docker1 flanneld-start[2950]: E0614 02:23:23.992106    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:24 docker1 flanneld-start[2950]: E0614 02:23:24.994719    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:25 docker1 flanneld-start[2950]: E0614 02:23:25.998629    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:27 docker1 flanneld-start[2950]: E0614 02:23:27.002486    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]
Jun 14 02:23:28 docker1 flanneld-start[2950]: E0614 02:23:28.006185    2950 network.go:102] failed to retrieve network config: 100: Key not found (/atomic.io) [11]

注意-etcd-prefix=/automic.io/network
flanel读取的网络配置是这个文件，这个文件是在

[root@docker1 ~]# cat /usr/lib/systemd/system/flanneld.service
[Unit]
Description=Flanneld overlay address etcd agent
After=network.target
After=network-online.target
Wants=network-online.target
After=etcd.service
Before=docker.service

[Service]
Type=notify
EnvironmentFile=/etc/sysconfig/flanneld
EnvironmentFile=-/etc/sysconfig/docker-network
ExecStart=/usr/bin/flanneld-start $FLANNEL_OPTIONS
ExecStartPost=/usr/libexec/flannel/mk-docker-opts.sh -k DOCKER_NETWORK_OPTIONS -d /run/flannel/docker
Restart=on-failure

[Install]
WantedBy=multi-user.target
RequiredBy=docker.service

[root@docker1 sysconfig]# cat flanneld
# Flanneld configuration options 

# etcd url location.  Point this to the server where etcd runs
FLANNEL_ETCD_ENDPOINTS="http://127.0.0.1:2379"

# etcd config key.  This is the configuration key that flannel queries
# For address range assignment
FLANNEL_ETCD_PREFIX="/atomic.io/network"

# Any additional options that you want to pass
#FLANNEL_OPTIONS=""

注意：

FLANNEL_ETCD_PREFIX="/atomic.io/network"

这个FLANNEL_ETCD_PREFIX须要etcdctl手动去创建

[root@docker1 ~]# etcdctl mk /atomic.io/network/config '{"Network":"172.17.0.0/16", "SubnetMin": "172.17.1.0", "SubnetMax": "172.17.254.0", "Backend":{"Type":"vxlan"}}'

再启动flannel，启动正常

[root@docker1 ~]# systemctl start flanneld && systemctl enable flanneld
Created symlink from /etc/systemd/system/multi-user.target.wants/flanneld.service to /usr/lib/systemd/system/flanneld.service.
Created symlink from /etc/systemd/system/docker.service.requires/flanneld.service to /usr/lib/systemd/system/flanneld.service.
[root@docker1 ~]#

[root@docker1 ~]# systemctl status flanneld
● flanneld.service - Flanneld overlay address etcd agent
   Loaded: loaded (/usr/lib/systemd/system/flanneld.service; disabled; vendor preset: disabled)
   Active: active (running) since Thu 2018-06-14 02:47:58 EDT; 11s ago
  Process: 3513 ExecStartPost=/usr/libexec/flannel/mk-docker-opts.sh -k DOCKER_NETWORK_OPTIONS -d /run/flannel/docker (code=exited, status=0/SUCCESS)
Main PID: 3475 (flanneld)
   Memory: 18.5M
   CGroup: /system.slice/flanneld.service
           └─3475 /usr/bin/flanneld -etcd-endpoints=http://127.0.0.1:2379 -etcd-prefix=/atomic.io/network

Jun 14 02:47:52 docker1 flanneld-start[3475]: E0614 02:47:52.150129    3475 network.go:102] failed to retrieve network co...) [14]
Jun 14 02:47:53 docker1 flanneld-start[3475]: E0614 02:47:53.152602    3475 network.go:102] failed to retrieve network co...) [14]
Jun 14 02:47:54 docker1 flanneld-start[3475]: E0614 02:47:54.155402    3475 network.go:102] failed to retrieve network co...) [14]
Jun 14 02:47:55 docker1 flanneld-start[3475]: E0614 02:47:55.158612    3475 network.go:102] failed to retrieve network co...) [14]
Jun 14 02:47:56 docker1 flanneld-start[3475]: E0614 02:47:56.164481    3475 network.go:102] failed to retrieve network co...) [14]
Jun 14 02:47:57 docker1 flanneld-start[3475]: E0614 02:47:57.168282    3475 network.go:102] failed to retrieve network co...) [14]
Jun 14 02:47:58 docker1 flanneld-start[3475]: I0614 02:47:58.179298    3475 local_manager.go:179] Picking subnet in range....254.0
Jun 14 02:47:58 docker1 flanneld-start[3475]: I0614 02:47:58.261220    3475 manager.go:250] Lease acquired: 172.17.21.0/24
Jun 14 02:47:58 docker1 flanneld-start[3475]: I0614 02:47:58.261993    3475 network.go:98] Watching for new subnet leases
Jun 14 02:47:58 docker1 systemd[1]: Started Flanneld overlay address etcd agent.
Hint: Some lines were ellipsized, use -l to show in full.

看看这个脚本

Process: 3513 ExecStartPost=/usr/libexec/flannel/mk-docker-opts.sh -k DOCKER_NETWORK_OPTIONS -d /run/flannel/docker (code=exited, status=0/SUCCESS)

flannel_env="/run/flannel/subnet.env"
docker_env="/run/docker_opts.env"
combined_opts_key="DOCKER_OPTS"
indiv_opts=false
combined_opts=false
ipmasq=true

检查下文件内容，我感受是根据这个文件来生成网段，不确认

[root@docker1 flannel]# cat /run/flannel/subnet.env
FLANNEL_NETWORK=172.17.0.0/16
FLANNEL_SUBNET=172.17.21.1/24
FLANNEL_MTU=1472
FLANNEL_IPMASQ=false

看看ip段

[root@docker1 ~]# ip a |grep flannel
11: flannel0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1472 qdisc pfifo_fast state UNKNOWN qlen 500
    inet 172.17.21.0/16 scope global flannel0
[root@docker1 ~]#

以上都是docker1上的操做

2.3 

docker2,docker3上的操做是同样的，我记录docker2上的操做

[root@docker2 ~]# yum -y install flannel

启动flannel

[root@docker2 ~]# flanneld -etcd-endpoints=http://192.168.211.140:2379 -iface=ens33 -etcd-prefix=/atomic.io/network
I0614 04:28:55.785204    2767 main.go:132] Installing signal handlers
I0614 04:28:55.785764    2767 manager.go:149] Using interface with name ens33 and address 192.168.211.154
I0614 04:28:55.785784    2767 manager.go:166] Defaulting external address to interface address (192.168.211.154)
E0614 04:28:55.786742    2767 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 192.168.211.140:2379: getsockopt: no route to host
E0614 04:28:57.788671    2767 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 192.168.211.140:2379: i/o timeout
E0614 04:28:59.791359    2767 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 192.168.211.140:2379: i/o timeout

报错了
这个错误是由于etcd默认只监听本机的2379端口

[root@docker1 ~]# cat /etc/etcd/etcd.conf
#[Member]
#ETCD_CORS=""
ETCD_DATA_DIR="/var/lib/etcd/default.etcd"
#ETCD_WAL_DIR=""
#ETCD_LISTEN_PEER_URLS="http://localhost:2380"
ETCD_LISTEN_CLIENT_URLS="http://localhost:2379"
#ETCD_MAX_SNAPSHOTS="5"
#ETCD_MAX_WALS="5"
ETCD_NAME="default"
#ETCD_SNAPSHOT_COUNT="100000"

把ETCD_LISTEN_CLIENT_URLS="http://localhost:2379"改为ETCD_LISTEN_CLIENT_URLS="http://0.0.0.0:2379"

从新启动etcd

[root@docker1 ~]# systemctl restart etcd
[root@docker1 ~]# systemctl status etcd
● etcd.service - Etcd Server
   Loaded: loaded (/usr/lib/systemd/system/etcd.service; enabled; vendor preset: disabled)
   Active: active (running) since Thu 2018-06-14 04:38:49 EDT; 1min 11s ago
Main PID: 3401 (etcd)
   Memory: 21.5M
   CGroup: /system.slice/etcd.service
           └─3401 /usr/bin/etcd --name=default --data-dir=/var/lib/etcd/default.etcd --listen-client-urls=http://0.0.0.0:23...

Jun 14 04:38:48 docker1 etcd[3401]: enabled capabilities for version 3.2
Jun 14 04:38:49 docker1 etcd[3401]: 8e9e05c52164694d is starting a new election at term 9
Jun 14 04:38:49 docker1 etcd[3401]: 8e9e05c52164694d became candidate at term 10
Jun 14 04:38:49 docker1 etcd[3401]: 8e9e05c52164694d received MsgVoteResp from 8e9e05c52164694d at term 10
Jun 14 04:38:49 docker1 etcd[3401]: 8e9e05c52164694d became leader at term 10
Jun 14 04:38:49 docker1 etcd[3401]: raft.node: 8e9e05c52164694d elected leader 8e9e05c52164694d at term 10
Jun 14 04:38:49 docker1 etcd[3401]: published {Name:default ClientURLs:[http://192.168.211.140:2379]} to cluster cdf8...3a8c32
Jun 14 04:38:49 docker1 etcd[3401]: ready to serve client requests
Jun 14 04:38:49 docker1 systemd[1]: Started Etcd Server.
Jun 14 04:38:49 docker1 etcd[3401]: serving insecure client requests on [::]:2379, this is strongly discouraged!
Hint: Some lines were ellipsized, use -l to show in full.
[root@docker1 ~]#

再启动仍是报错 

[root@docker2 ~]# systemctl status flanneld -l
● flanneld.service - Flanneld overlay address etcd agent
   Loaded: loaded (/usr/lib/systemd/system/flanneld.service; disabled; vendor preset: disabled)
   Active: inactive (dead)

Jun 14 04:21:53 docker2 flanneld-start[2706]: E0614 04:21:53.879476    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:21:54 docker2 flanneld-start[2706]: E0614 04:21:54.880962    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:21:55 docker2 flanneld-start[2706]: E0614 04:21:55.882332    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:21:56 docker2 flanneld-start[2706]: E0614 04:21:56.887002    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:21:57 docker2 flanneld-start[2706]: E0614 04:21:57.888246    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:21:58 docker2 flanneld-start[2706]: E0614 04:21:58.889903    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:21:59 docker2 flanneld-start[2706]: E0614 04:21:59.891323    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:22:00 docker2 flanneld-start[2706]: E0614 04:22:00.892229    2706 network.go:102] failed to retrieve network config: client: etcd cluster is unavailable or misconfigured; error #0: dial tcp 127.0.0.1:2379: getsockopt: connection refused
Jun 14 04:22:01 docker2 systemd[1]: Stopped Flanneld overlay address etcd agent.
Jun 14 04:22:01 docker2 flanneld-start[2706]: I0614 04:22:01.105679    2706 main.go:172] Exiting...
[root@docker2 ~]#

拒绝链接，应该是防火墙的问题了

关闭docker1的防火墙

[root@docker2 ~]# flanneld -etcd-endpoints=http://192.168.211.140:2379 -iface=ens33 -etcd-prefix=/atomic.io/network &
[1] 2938
[root@docker2 ~]# I0614 04:44:03.522494    2938 main.go:132] Installing signal handlers
I0614 04:44:03.523151    2938 manager.go:149] Using interface with name ens33 and address 192.168.211.154
I0614 04:44:03.523174    2938 manager.go:166] Defaulting external address to interface address (192.168.211.154)
I0614 04:44:03.530498    2938 local_manager.go:134] Found lease (172.17.41.0/24) for current IP (192.168.211.154), reusing
I0614 04:44:03.546625    2938 manager.go:250] Lease acquired: 172.17.41.0/24
I0614 04:44:03.547228    2938 network.go:98] Watching for new subnet leases
I0614 04:44:03.558669    2938 network.go:191] Subnet added: 172.17.21.0/24

[root@docker2 ~]# ip a |grep flannel
8: flannel0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1472 qdisc pfifo_fast state UNKNOWN group default qlen 500
    inet 172.17.41.0/16 scope global flannel0
[root@docker2 ~]#

启动了

有点奇怪，重启docker1后，能够进来了，不须要添加开放2379的规则

2.4 
docker3作同样的操做

3.分析flannel网络
 
3.1
上面把基本架构部署好了，具体以下:docker1安装了etcd，docker1 docker2 docker3都安装了flannel

在docker1上查看设置分配的网段和已经分配的网段

设置分配的网段

[root@docker1 ~]#  etcdctl get atomic.io/network/config
{"Network":"172.17.0.0/16", "SubnetMin": "172.17.1.0", "SubnetMax": "172.17.254.0", "Backend":{"Type":"vxlan"}}

已经分配的网段

[root@docker1 ~]# etcdctl ls atomic.io/network/subnets
/atomic.io/network/subnets/172.17.21.0-24
/atomic.io/network/subnets/172.17.41.0-24
/atomic.io/network/subnets/172.17.95.0-24
[root@docker1 ~]#

3.2
docker中使用flannel网络

配置docker链接flannel，我这里用docker2和docker3
 
docker经过修改docker配置文件
/etc/systemd/system/docker.service
设置 --bip 和--mtu
链接flannel

--bip --mtu的值   来自/run/flannel/subnet.env

[root@docker2 ~]#  cat /run/flannel/subnet.env
FLANNEL_NETWORK=172.17.0.0/16
FLANNEL_SUBNET=172.17.65.1/24
FLANNEL_MTU=1450
FLANNEL_IPMASQ=false

--bip  是 FLANNEL_SUBNET的值
--mtu 是 FLANNEL_MTU的值

在docker.service加上这两个值

[root@docker2 ~]# cat /etc/systemd/system/docker.service
[Unit]
Description=Docker Application Container Engine
After=network.target

[Service]
Type=notify
ExecStart=/usr/bin/dockerd -H tcp://0.0.0.0:2376 -H unix:///var/run/docker.sock --storage-driver devicemapper --tlsverify --tlscacert /etc/docker/ca.pem --tlscert /etc/docker/server.pem --tlskey /etc/docker/server-key.pem --label provider=generic --bip=172.17.65.1/24 --mtu=1450
ExecReload=/bin/kill -s HUP
MountFlags=slave

重启docker

[root@docker2 ~]# systemctl daemon-reload
[root@docker2 ~]# systemctl restart docker.service

3.2
简易分析

docker链接上flannel后，网络路由和bridge 状况，参考以下

[root@docker2 ~]# ip r
default via 192.168.211.2 dev ens33 proto dhcp metric 100
172.17.0.0/16 dev flannel.1
172.17.65.0/24 dev docker0 proto kernel scope link src 172.17.65.1
172.18.0.0/16 dev docker_gwbridge proto kernel scope link src 172.18.0.1
192.168.211.0/24 dev ens33 proto kernel scope link src 192.168.211.154 metric 100

[root@docker2 ~]# brctl show
bridge name        bridge id                STP enabled        interfaces
docker0                8000.02427f17e635        no                veth7680282
docker_gwbridge                8000.024266f01344        no               
[root@docker2 ~]#

没有生成新的网桥，使用默认的docker0

172.17.65.0 同一docker主机 容器经过docker0链接
172.17.0.0   不一样docker主机 容器经过flannel.1转发

3.3 
容器链接flannel网络

[root@docker2 ~]# docker run -itd --name bbox1 busybox
dc344e4b30e48bbc5b914edc3724e43d56fa0ee7abf97246dc35ce57b6cf872c
[root@docker2 ~]# docker exec bbox1 ip r
default via 172.17.65.1 dev eth0
172.17.65.0/24 dev eth0 scope link  src 172.17.65.2
[root@docker2 ~]#

[root@docker3 ~]# docker run -itd --name bbox2 busybox
e9e824f93e8dedb498f436b169ed8dcb85bc951f4d05ae4f254aad1e3d538a8a
[root@docker3 ~]# docker exec bbox2 ip r
default via 172.17.16.1 dev eth0
172.17.16.0/24 dev eth0 scope link  src 172.17.16.2
[root@docker3 ~]#

互ping

[root@docker2 ~]# docker exec bbox1 ping -c 5 172.17.16.2
PING 172.17.16.2 (172.17.16.2): 56 data bytes
64 bytes from 172.17.16.2: seq=0 ttl=60 time=3.274 ms
64 bytes from 172.17.16.2: seq=1 ttl=60 time=1.356 ms
^C
[root@docker2 ~]#

 [root@docker3 ~]# docker exec bbox2 ping -c 5 172.17.65.2
PING 172.17.65.2 (172.17.65.2): 56 data bytes
64 bytes from 172.17.65.2: seq=0 ttl=60 time=2.995 ms
64 bytes from 172.17.65.2: seq=1 ttl=60 time=1.396 ms
64 bytes from 172.17.65.2: seq=2 ttl=60 time=1.650 ms
^C
[root@docker3 ~]#

分析数据流

从bbox1 ping 172.17.16.2

看看它的默认路由

[root@docker2 ~]# docker exec bbox1 ip r
default via 172.17.65.1 dev eth0
172.17.65.0/24 dev eth0 scope link  src 172.17.65.2
[root@docker2 ~]#

目的地址 172.17.16.2不在直连网络，所以数据包从default路由出。default路由的地址时 172.17.65.1，这个地址就是docker0的地址

[root@docker2 ~]# ip a |grep docker0
4: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc noqueue state UP group default
    inet 172.17.65.1/24 brd 172.17.65.255 scope global docker0
24: veth63d6978@if23: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc noqueue master docker0 state UP group default
[root@docker2 ~]#

数据到达docker0后，发现这个数据包的地址是172.17.16.2，并非给本身，寻找下一跳
看看node上的路由表

[root@docker2 ~]# ip r
default via 192.168.211.2 dev ens33 proto dhcp metric 100
172.17.0.0/16 dev flannel.1
172.17.65.0/24 dev docker0 proto kernel scope link src 172.17.65.1
172.18.0.0/16 dev docker_gwbridge proto kernel scope link src 172.18.0.1
192.168.211.0/24 dev ens33 proto kernel scope link src 192.168.211.154 metric 100
[root@docker2 ~]#

匹配到172.17.0.0/16这条路由，这是直连路由，数据送到flannel.1上

flannel.1收到数据包，本身不是目的地，须要发数据发送出去，数据包沿着网络协议向下流动，在二层封装以太包，填写目的mac地址。
这时发出arp“who is 172.17.16.2"

flannel.1是vxlan设备，vxlan并不会在二层发arp包，而是由linux kernel的 “L3 MISS"事件，将arp发到用户空间和flanneld程序。

linux kernel的 “L3 MISS"事件参数由下面的参数设置
[root@docker2 ~]# cat /proc/sys/net/ipv4/neigh/flannel.1/app_solicit
3
[root@docker2 ~]#

flanneld程序收到“L3 MISS”内核事件以及ARP请求后，并不会向外网发送arp request，而是从etcd查找匹配该地址的子网的vtep信息。

[root@docker2 ~]#  curl -L http://192.168.211.140:2379/v2/keys/atomic.io/network/subnets/172.17.16.0-24
{"action":"get","node":{"key":"/atomic.io/network/subnets/172.17.16.0-24","value":"{\"PublicIP\":\"192.168.211.153\",\"BackendType\":\"vxlan\",\"BackendData\":{\"VtepMAC\":\"d2:72:c5:90:ff:8c\"}}","expiration":"2018-06-20T06:49:24.673562899Z","ttl":83016,"modifiedIndex":98,"createdIndex":98}}
[root@docker2 ~]#

flanneld从etcd中找到答案

subnets:172.17.16.0-24
PublicIP:192.168.211.153
VtepMAC:d2:72:c5:90:ff:8c

VtepMAC:d2:72:c5:90:ff:8c 这个地址谁呢？

到192.168.211.153也就是这里的docker3检查下

[root@docker3 ~]# ip -d link show

11: flannel.1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc noqueue state UNKNOWN mode DEFAULT group default
    link/ether d2:72:c5:90:ff:8c brd ff:ff:ff:ff:ff:ff promiscuity 0
    vxlan id 1 local 192.168.211.153 dev ens33 srcport 0 0 dstport 8472 nolearning ageing 300 noudpcsum noudp6zerocsumtx noudp6zerocsumrx 

能够看到docker3的flannel.1的mac地址就是

找到目的地后，flanneld将查询到的信息存入arp缓存

[root@docker2 ~]# ip n
192.168.211.254 dev ens33 lladdr 00:50:56:ea:e1:f4 STALE
172.17.16.2 dev flannel.1 lladdr d2:72:c5:90:ff:8c STALE
192.168.211.2 dev ens33 lladdr 00:50:56:fd:b3:89 STALE
192.168.211.153 dev ens33 lladdr 00:0c:29:93:2c:89 STALE
192.168.211.1 dev ens33 lladdr 00:50:56:c0:00:08 DELAY
172.17.65.2 dev docker0 lladdr 02:42:ac:11:41:02 STALE
192.168.211.140 dev ens33 lladdr 00:0c:29:f9:b7:d2 DELAY
[root@docker2 ~]#

最后封装vxlan包，发送到目的地

4.
flannel 为每一个主机分配了独立的 subnet但 flannel.1 将这些 subnet 链接起来了相互之间能够路由。本质上flannel 将各主机上相互独立的 docker0 容器网络组成了一个互通的大网络实现了容器跨主机通讯。flannel 没有提供隔离。

5.
host-gw

flannel支持多种backend,host-gw是flannel的另外一种backend.
与vxlan不一样,host-gw不会封装数据包.而是在主机路由表中建立到其余主机subnet的路由条目,实现容器跨主机通信.

设置backend
修改下前面设置的,把backend改为host-gw

[root@docker1 ~]# etcdctl set atomic.io/network/config '{"Network":"172.17.0.0/16", "SubnetMin": "172.17.1.0", "SubnetMax": "172.17.254.0", "Backend":{"Type":"host-gw"}}'
{"Network":"172.17.0.0/16", "SubnetMin": "172.17.1.0", "SubnetMax": "172.17.254.0", "Backend":{"Type":"host-gw"}}
[root@docker1 ~]# etcdctl get atomic.io/network/config
{"Network":"172.17.0.0/16", "SubnetMin": "172.17.1.0", "SubnetMax": "172.17.254.0", "Backend":{"Type":"host-gw"}}
[root@docker1 ~]#

在docker2,docker3从新启动flanneld进程.

[root@docker2 ~]# flanneld -etcd-endpoints=http://192.168.211.140:2379 -iface=ens33 -etcd-prefix=/atomic.io/network &

检查下路由表

[root@docker2 ~]# ip r
default via 192.168.211.2 dev ens33 proto dhcp metric 100
169.254.0.0/16 dev ens33 scope link metric 1002
172.17.16.0/24 via 192.168.211.153 dev ens33
172.17.65.0/24 dev docker0 proto kernel scope link src 172.17.65.1
172.18.0.0/16 dev docker_gwbridge proto kernel scope link src 172.18.0.1
192.168.211.0/24 dev ens33 proto kernel scope link src 192.168.211.154 metric 100
[root@docker2 ~]#

[root@docker3 ~]# ip r
default via 192.168.211.2 dev ens33 proto dhcp metric 100
169.254.0.0/16 dev ens33 scope link metric 1002
172.17.16.0/24 dev docker0 proto kernel scope link src 172.17.16.1
172.17.65.0/24 via 192.168.211.154 dev ens33
172.18.0.0/16 dev docker_gwbridge proto kernel scope link src 172.18.0.1
192.168.211.0/24 dev ens33 proto kernel scope link src 192.168.211.153 metric 100
[root@docker3 ~]#

172.17.16.0/24 via 192.168.211.153 dev ens33  docker2
172.17.65.0/24 via 192.168.211.154 dev ens33  docker3

出现了相对应的路由条目

须要修改mtu而且重启docker
mtu值前面已经有过说明，根据下面的值来修改

[root@docker3 ~]# cat /run/flannel/subnet.env
FLANNEL_NETWORK=172.17.0.0/16
FLANNEL_SUBNET=172.17.16.1/24
FLANNEL_MTU=1500
FLANNEL_IPMASQ=false
[root@docker3 ~]#

[root@docker3 ~]# sed -i 's/1450/1500/g'  /etc/systemd/system/docker.service

重启docker

[root@docker3 ~]# systemctl daemon-reload
[root@docker3 ~]# systemctl restart docker
[root@docker3 ~]#

经过容器数据走向分析下

[root@docker2 ~]# docker exec bbox1 ping 172.17.16.2
PING 172.17.16.2 (172.17.16.2): 56 data bytes
64 bytes from 172.17.16.2: seq=0 ttl=62 time=1.851 ms
64 bytes from 172.17.16.2: seq=1 ttl=62 time=0.946 ms
64 bytes from 172.17.16.2: seq=2 ttl=62 time=0.972 ms
^C
[root@docker2 ~]# docker exec bbox1 ip  r
default via 172.17.65.1 dev eth0
172.17.65.0/24 dev eth0 scope link  src 172.17.65.2
[root@docker2 ~]#

走默认路由172.17.65.1

[root@docker2 ~]# ip a |grep docker0
4: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
    inet 172.17.65.1/24 brd 172.17.65.255 scope global docker0
7: vetha9f972a@if6: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master docker0 state UP group default
[root@docker2 ~]#

数据到达docker0

[root@docker2 ~]# ip r
default via 192.168.211.2 dev ens33 proto dhcp metric 100
169.254.0.0/16 dev ens33 scope link metric 1002
172.17.16.0/24 via 192.168.211.153 dev ens33
172.17.65.0/24 dev docker0 proto kernel scope link src 172.17.65.1
172.18.0.0/16 dev docker_gwbridge proto kernel scope link src 172.18.0.1
192.168.211.0/24 dev ens33 proto kernel scope link src 192.168.211.154 metric 100
[root@docker2 ~]#

匹配到172.17.16.0/24 via 192.168.211.153 dev ens33

直接发送数据过去.

6.
vxlan和host-gw的简单比较

host-gw 把每一个主机配置成网关,主机知道其余主机的subnet和转发地址.
vxlan是在主机间创建隧道.
不一样的主机在一个大的网内.

vxlan须要对数据进行打包拆包,性能低于host-gw