Zabbix 监控 Cisco ASA5525 流量

简介：

Zabbix 监控 Cisco ASA5525 网络接口流量

1、Zabbix 支持 SNMP、Cisco 开启 SNMP

2、测试

shell > snmpwalk -v 2c -c public 192.168.2.254 system  # 查看系统信息
SNMPv2-MIB::sysDescr.0 = STRING: Cisco Adaptive Security Appliance Version 8.6(1)2
SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.9.1.1408
DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3248815000) 376 days, 0:29:10.00
SNMPv2-MIB::sysContact.0 = STRING: 
SNMPv2-MIB::sysName.0 = STRING: ciscoasa
SNMPv2-MIB::sysLocation.0 = STRING: 
SNMPv2-MIB::sysServices.0 = INTEGER: 4

# -v 指定版本，-c 指定共同体名，IP，指令

shell > snmpwalk -v 2c -c public 192.168.2.254 interface  # 查看接口信息

# IF-MIB::ifDescr 接口名称
# IF-MIB::ifType 类型
# IF-MIB::ifSpeed 速率
# IF-MIB::ifMtu MTU
# IF-MIB::ifPhysAddress MAC
# IF-MIB::ifAdminStatus 状态
# IF-MIB::ifInOctets 传输字节数

# 等

3、确认须要监控网络接口

ciscoasa > show running-config interface
!
interface GigabitEthernet0/0
 duplex full
 nameif outside-1
 security-level 0
 ip address xx.xx.xx.xx 255.255.255.224 

# Cisco ASA 查看发现，GigabitEthernet0/0 为 outside-1 即外网接口，且配置着公网IP

shell > snmpwalk -v 2c -c public 192.168.2.254 ifDescr
IF-MIB::ifDescr.2 = STRING: Adaptive Security Appliance 'asa_mgmt_plane' interface
IF-MIB::ifDescr.3 = STRING: Adaptive Security Appliance 'outside-1' interface
IF-MIB::ifDescr.4 = STRING: Adaptive Security Appliance 'GigabitEthernet0/1' interface
IF-MIB::ifDescr.5 = STRING: Adaptive Security Appliance 'inside' interface
IF-MIB::ifDescr.6 = STRING: Adaptive Security Appliance 'GigabitEthernet0/3' interface
IF-MIB::ifDescr.7 = STRING: Adaptive Security Appliance 'GigabitEthernet0/4' interface
IF-MIB::ifDescr.8 = STRING: Adaptive Security Appliance 'GigabitEthernet0/5' interface
IF-MIB::ifDescr.9 = STRING: Adaptive Security Appliance 'GigabitEthernet0/6' interface
IF-MIB::ifDescr.10 = STRING: Adaptive Security Appliance 'GigabitEthernet0/7' interface
IF-MIB::ifDescr.11 = STRING: Adaptive Security Appliance 'Internal-Data0/1' interface
IF-MIB::ifDescr.12 = STRING: Adaptive Security Appliance 'cplane' interface
IF-MIB::ifDescr.13 = STRING: Adaptive Security Appliance 'mgmt_plane_int_tap' interface
IF-MIB::ifDescr.14 = STRING: Adaptive Security Appliance 'Management0/0' interface
IF-MIB::ifDescr.15 = STRING: Adaptive Security Appliance 'Virtual254' interface

# 服务器上查找，返现 outside-1 对应的设备 ID 为 IF-MIB::ifDescr.3

shell > snmpwalk -v 2c -c public 192.168.2.254 IF-MIB::ifInOctets.3   # 外网口进方向
IF-MIB::ifInOctets.3 = Counter32: 2965376258

shell > snmpwalk -v 2c -c public 192.168.2.254 IF-MIB::ifOutOctets.3  # 外网口出方向
IF-MIB::ifOutOctets.3 = Counter32: 3522107956

4、建立主机、模板

一、主机

建立主机 -> SNMP 192.168.2.254 161 -> 建立

二、模板

建立模板 -> 模板名称 Cisco -> 群组 Templates -> 建立

建立应用 -> network interface

建立监控项 -> 名称 GigabitEthernet0/0 - In
           -> 类型 SNMPv2 端点代理模式
           -> 键值 ifHCInOctets.3
           -> SNMP OID IF-MIB::ifHCInOctets.3
           -> SNMP community public
           -> 单位 bps
           -> 使用自定倍数 8
           -> 存储值 差量(每秒速率)
           -> 应用集 network interface
           -> 建立

# 拿到的是 byte 要转换成 bit 即 bps，1 byte = 8 bit，因此要设置倍数为 8
# 照这样设置 GigabitEthernet0/0 - Out 便可，注意键值为 ifHCOutOctets.3，OID 为 OID IF-MIB::ifHCOutOctets.3

三、图形

建立图形 -> 名称 GigabitEthernet0/0 -> 加入监控项 -> 绘图风格 梯度线 -> 设置颜色 -> 建立

5、为主机添加模板

主机 -> 模板 -> 选择模板 -> Cisco -> 添加 -> 更新

# 收工 ！