1.5 kyLin-V3.0-OneNET-裸机-RTOS
RTOS代码
综合应用
实验一 麒麟座V3.0综合应用代码-UCOS-EDP
1.修改2个参数
ONETNET_INFO oneNetInfo = {"24407565", "Ij=Oeo7lxf18xR73V4aRq8BBTHc=",
"183.230.40.39", "876",
1,
0, 0, 0, 1, 0};
2.现象
串口
SHT20 :Ok[2018-01-02 03:29:20.295]
ADXL362 :Ok[2018-01-02 03:29:20.295]
EEPROM :Ok[2018-01-02 03:29:20.298]
1.ssid_pswd in ROM[2018-01-02 03:29:20.298]
2.DEVID: 24407565, APIKEY: Ij=Oeo7lxf18xR73V4aRq8BBTHc=[2018-01-02 03:29:20.303]
3.Hardware init OK[2018-01-02 03:29:20.306]
4.OSStart[2018-01-02 03:29:20.306]
Tips:ESP8266_Reset[2018-01-02 03:29:20.541]
ESP8266 Got IP[2018-01-02 03:29:22.871]
NET Device :Ok[2018-01-02 03:29:22.871]
Tips:CLOSE[2018-01-02 03:29:22.896]
AT+CIPSTART="UDP","edu.ntp.org.cn",123[2018-01-02 03:29:25.392]
Tips:CLOSE[2018-01-02 03:29:25.517]
UTC Time: 2018-1-2 15:29:27[2018-01-02 03:29:25.580]
Tips:CLOSE[2018-01-02 03:29:26.140]
AT+CIPSTART="TCP","183.230.40.33",80[2018-01-02 03:29:28.606]
Get: ip: 183.230.40.39, port: 876[2018-01-02 03:29:28.838]
Tips:CLOSE[2018-01-02 03:29:28.838]
Tips:AT+CIPSTART="TCP","183.230.40.39",876[2018-01-02 03:29:28.926]
Tips:ESP8266 STA_Mode OK[2018-01-02 03:29:29.016]
OneNet_DevLink[2018-01-02 03:29:29.024]
DEVID: 24407565, APIKEY: Ij=Oeo7lxf18xR73V4aRq8BBTHc=[2018-01-02 03:29:29.024]
Tips:连接成功[2018-01-02 03:29:29.104]
Tips:OneNet_SendData-EDP_TYPE3[2018-01-02 03:29:29.205]
Send 232 Bytes[2018-01-02 03:29:29.220]
Tips:Send Ok[2018-01-02 03:29:29.445]
Tips:OneNet_SendData-EDP_TYPE3[2018-01-02 03:29:35.953]
Send 232 Bytes[2018-01-02 03:29:35.961]
网页上
UCOS-EDP "在线"
数据流展示
12种数据流 随时间变化而变化
======================================================================================
实验二 麒麟座V3.0综合应用代码-FreeRTOS-EDP
方法和现象同上,注意一点 修改的二个参数必须同开发者中心里面的二个参数一模一样,多一个空格都不行,切记切记!(我就不截图了)
======================================================================================
下面的与不跑系统(我习惯叫"裸奔")的现象一模一样,我就不一一演示截图了
3.麒麟座V3.0综合应用代码-UCOS-HTTP
4.麒麟座V3.0综合应用代码-FreeRTOS-HTTP
5.麒麟座V3.0综合应用代码-UCOS-MQTT
6.麒麟座V3.0综合应用代码-FreeRTOS-MQTT